"Moć je geometrija spojena sa umetničkim nemirom", Euripid  
moNGeometrija 2012
MoNGeometrija 2012

3rd International Scientific Conference / Treći međunarodni naučni skup


moNGeometrija 2012

Proceedings / Zbornik radova

 

June 21st – 24th 2012

 

Download PDF (182MB)

 


 

 

MoNGeometrija 2012


Second Announcement

 


Guidelines For MS Word manuscripts preparing for Proceeding of

3rd International Conference on Geometry and Graphics MoNGeometrija 2012


Abstract deadline: 29 February 2012

Manuscripts deadline: 30 April 2012


 

1. GENERAL GUIDELINES

English is the official language of the Conference. The number of manuscript pages should be four pages or more. Manuscript must be prepared as MS Word (doc) file and sent as attachment by e-mail to the following address:

 

Ova adresa el. pošte zaštićena je od spam napada, treba omogućiti JavaSkript da biste je videli

 

2. TECHNICAL DETAILS

The following Page Setup parameters should be selected:

Paper Size: A4;

Margins - Top: 2,5 cm; Bottom: 2,5 cm; Left: 3 cm; Right: 3 cm.

Font is Arial, 12 pt, unless it is specified differently by this guideline. The

following Paragraph formatting parameters should be selected:

General - Alignment: Justified; Outline level: Body text.

Indentation - Left: 0 cm, Right: 0 cm, Special: First line, By: 1,27cm

Spacing – Before: 0 cm, After: 0 cm, Line spacing: Single.

 

3. FIRST PAGE

First page should be formatted as specified below:

Five (5) blank lines (11pt);

Paper title (Font: Arial, 13pt, bold, center, Capital letters);

One (1) blank line (13pt);

Names of authors (12 pt, bold, centered, first letter – capital), each author in

different line, omitting the academic titles; (Names, titles, affiliations and addresses of all authors should be given)

Two (2) blank lines (12pt)

Abstract (12 pt, bold, center), as title

One (1) blank line (12 pt)

Content of Abstract (12 pt, italic) which should not exceed 20 lines (12 pt)

One (1) blank line (10 pt)

Key words: (12 pt, bold) followed by five (5) key words of the manuscript

Three (3) blank lines (10pt)

 

4. CHAPTER TITLES

The following parameters should be selected:

Font: Arial, 12pt, bold, Capital letters, centered and numbered (1., 2., 3.,...).

Format, Paragraph, Spacing: before - 6 pt; after – 6 pt.

One (1) blank line (12 pt) should be inserted between the chapter title and the last

line of the preceding paragraph.

4.1. Chapter subtitles

The following parameters should be selected:

Font: Arial, 12pt, bold, First letter capital, centered and numbered (1.1., 1.2., 1.3. , ...).

Format, Paragraph, Spacing: before - 6 pt; after – 6 pt.

One (1) blank line (12 pt) should be inserted between the chapter title and the last

line of the preceding paragraph.

 

5. TABLES

Tables should be numbered and entitled (10 pt, italic, centered) at the beginning (top side) of the table. One (1) blank lines (10 pt) should be inserted before the table title and after the body of the table.

 

6. DRAWINGS, FIGURES AND PHOTOGRAPHS

Drawings, figures and photographs should be numbered and entitled (11 pt, italic, centered) at the bottom side. Two (2) blank lines (10 pt) should be inserted before and after each drawing, figure or photograph.

 

7. FORMULAS

One (1) blank line (12 pt) should be inserted before and after each formula. Formulas should be numbered.

 

8. FOOTNOTE

The following parameters should be selected:

Font: Arial (10 pt)

Reference

Footnote: Bottom of the page

Format, Number format: 1, 2, 3, …

Start at: 1

Numbering: Continuous

 

9. LITERATURE

Literature (11 pt) should be given in alphabetical order, as it is shown in the following example:

Format / Bulets and Numbering / Numbered / Customize / Customize Nembered List:

Number position Left

Aligned at 0.63cm

Tab space after 1.27cm

Intent at 1.27cm

 

 

  1. Humbert, L., Carlioz, H., Baudoin, A., Skalli, W., Mitton, D.: 3D Evaluation of the acetabular coverage assessed by biplanar X-rays or single anteroposterior X-ray compared with CT-scan, Computer Methods in Biomechanics and Biomedical Engineering, Vol. 11, No. 3, 2008, pp. 257–262.
  2. Chronis P.N.: Mechanisms, linkages and Mechanical Controls, International Student Edition, McGraw-Hill, London, 1965.
  3. Đurić S.: Mehanika - Dinamika i teorija oscilacija, Mašinski fakultet, Beograd, 1981.

 

 

First Announcement

 

Dear Colleagues,

 

we would like to inform you that the next International Conference MONGEOMETRIJA 2012 will be held from 21st to 24th June 2012 at the Faculty of Technical Sciences in Novi Sad, Serbia.

 

Topics of interest of the Conference can be found at the site of Serbian Society of Geometry and Graphics

 

http://www.mongeometrija.com/konferencije/topics

 

It would be our great honor and pleasure if you participate at the Conference.

 

Best regards,

 

PhD Ratko Obradovic, Associate Professor

Faculty of Technical Sciences

Serbia

 

http://www.racunarska-grafika.com/kratki-filmovi

 

Email: Ova adresa el. pošte zaštićena je od spam napada, treba omogućiti JavaSkript da biste je videli

 
Scientific Review Committee

Ph.D. Hellmuth Stachel, University of Technology Vienna, Austria
Ph D. Zvonko Tomanovi
ć, University of Montenegro, Montenegro

Ph.D. Milena Stavrić, TU Graz, Institut für Architektur und Medien, Austria
Ph.D. Sonja Gorjanc, Faculty of Civil Engineering, Zagreb, Croatia, Hrvatska
Ph.D. Carmen Marza, Technical University of Cluj-Napoca, Romania

Ph.D. Jelisava Kalezić, University of Montenegro, Montenegro

Ph.D. Risto Tashevski, UKIM, Skopje, Republic of Macedonia

Ph.D. Albert Wiltsche, TU Graz, Austria

Ph.D. Attila Bölcskei, Szent István University, Budapest, Hungary

Ph.D. Žiga Turk, University of Ljubljana, Slovenia

Ph.D. Laszlo Voros, University of Pecs, Hungary

Ph.D. Džafer Kudumović, University of Tuzla, Bosnia and Hercegovina

Ph.D. Emil Molnar, Technical University of Budapest, Hungary
Ph.D. Gordana Fontana-Giusti, Centre for Research in European Architecture, London, England

Ph.D. Olga Timcenko, Aalborg University in Copenhagen,Denmark

Ph.D. Viktor Milejkovskyi, Kyiv National University of Construction and Architecture, Ukraine 
Ph.D. Svetlana Shambina, Russian Peoples Friendship University, Engineering Faculty, Moscow, Russia
Ph.D. Ratko Obradović, Faculty of Technical Sciences, Novi Sad, Serbia

Ph.D. Radovan Štulić, Faculty of Technical Sciences, Novi Sad, Serbia

Ph.D. Radojka Gligorić, Faculty of Agriculture, Novi Sad, Serbia

Ph.D. Tima Segedinac, Higher Technical School of Professional Studies in Novi Sad, Serbia

Ph.D. Branislav Popkonstantinović, Faculty of Mechanical Engineering, Belgrade, Serbia

Ph.D. Ljubica Velimirović, Faculty of Science and Mathematics, Niš, Serbia
Ph.D. Marija Obradović, Faculty of Civil Engineering, Belgrade, Serbia

Ph.D. Dragan Ivetić, Faculty of Technical Sciences, Novi Sad, Serbia

Ph.D. Sonja Krasić, Faculty of Civil Engineering and Architecture, Niš, Serbia

Ph.D. Aleksandar Veg, Faculty of Mechanical Engineering, Belgrade
Ph.D. Aleksandar Čučaković, Faculty of Civil Engineering, Belgrade

Ph.D. Miodrag Nestorović, Faculty of Architecture, Belgrade

 

Ph.D. Ivana Marcikić, Faculty of Applied Arts, Belgrade

M.Sc. Branko Pavić, Faculty of Architecture, Belgrade
M.Sc. Miloš Vujanović, Academy of Arts, Novi Sad, Serbia

Professor Đorđe Zloković, Member of Serbian Academy of Sciences and Arts, Department of Technical Sciences, Belgrade
Ph.D. Hranislav Anđelković, Retired full professor, Faculty of Civil Engineering and Architecture, Niš
Ph.D. Miroslav Marković, Retired full professor, Faculty of Civil Engineering and Architecture, Niš

Ph.D. Lazar Dovniković, Retired full professor, Faculty of Technical Sciences, Novi Sad